IndiaBIX
IndiaBIX
Start typing & press "Enter" or "ESC" to close
  • Home
  • Jobs
  • Results
  • Current Affairs
  • GK
  • Online Test
  • HR Interview
  • BLOG

Voltage Regulators - General Questions (3)

  • Home
  • Electronics & Communication Engineering
  • Electronic Devices and Circuit Theory
  • Voltage Regulators - General Questions
Directions to Solve

Voltage Regulators - General Questions

17. 

Voltage regulation requires

A. only line regulation.
B. only load regulation.
C. a constant load.
D. load and line regulation.

Answer: Option D

Explanation:

No answer description available for this question.
View Answer Discuss Workspace Report

18. 

Which component(s) set(s) the voltage across the load in a basic transistor shunt regulator?

A. Zener diode
B. Transistor base-emitter voltage
C. Both the Zener diode and the transistor base-emitter voltage
D. None of the above

Answer: Option C

Explanation:

No answer description available for this question.
View Answer Discuss Workspace Report

19. 

In this op-amp series regulator circuit, which of the following components is the comparator circuit?

mcq15_02200

A. Op-amp
B. Transistor Q1
C. R1 and R2 resistors
D. Zener diode

Answer: Option A

Explanation:

No answer description available for this question.
View Answer Discuss Workspace Report

20. 

What are the typical values of Vref and Iadj for the LM317 adjustable voltage regulator?

A. 1.0 V, 100 mA
B. 1.5 V, 100 mA
C. 1.25 V, 100 μA
D. 1.25 V, 10 mA

Answer: Option C

Explanation:

No answer description available for this question.
View Answer Discuss Workspace Report

21. 

How many terminals does a 7800 series IC regulator have?

A. 2
B. 3
C. 4
D. none of the above

Answer: Option B

Explanation:

No answer description available for this question.
View Answer Discuss Workspace Report

22. 

Calculate the ripple of a capacitor filter for a peak rectified voltage of 40 V, a capacitor value C = 75 mu (3)1 F, and a load current of 40 mA.

A. 3.2%
B. 3.59%
C. 4.03%
D. 4.59%

Answer: Option A

Explanation:

No answer description available for this question.
View Answer Discuss Workspace Report

23. 

Refer to the given figure. If a solder splash shorted the ends of R1 to each other,

mcq18_1006_1a (3)

A. the op-amp would fail.
B. Q1 would open.
C. the output voltage would not change.
D. the zener would fail.

Answer: Option D

Explanation:

No answer description available for this question.
View Answer Discuss Workspace Report

24. 

How many diodes conduct in the full-wave bridge rectifier while the capacitor is being charged?

A. 1
B. 2
C. 3
D. 4

Answer: Option B

Explanation:

No answer description available for this question.
View Answer Discuss Workspace Report

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8

Questions & Answers

Aptitude Chemical Engineering Civil Engineering Computer Science & Engineering Current Affairs Data Interpretation Electrical & Electronics Engineering Electronics & Communication Engineering General Knowledge Logical Reasoning Mechanical Engineering Non Verbal Reasoning Verbal Ability Verbal Reasoning

Interviews

HR Interview

Jobs

Sarkari Jobs

Results

Rojgar ResultSarkari Result

Admission

Admission 2023

Admit Card

Admit Card 2023

Answer Key

Answer Key 2023
copyright
Privacy Policy
© 2026 IndiaBIX. All Rights Reserved.

Report